β Must-know
π An aqueous buffer must contain a weak acid/base conjugate pair and a substantial amount of both components.
Further detail
A component is not present in a substantial amount if its concentration is more than 10 times that of the other buffer component.
An aqueous solution containing H2CO3 alone is not a buffer because it does not contain a substantial amount of HCO3-.
Ingested ethylene glycol leads to glycolic acid formation, which decreases blood pH and causes acidosis.
The main blood buffer system contains H2CO3 and HCO3-.
When base is added to the blood buffer, H2CO3 donates a proton according to .
When acid is added to the blood buffer, HCO3- accepts a proton according to .
The weak acid neutralizes added base; the conjugate base neutralizes added acid.
β Must-know
π Formula - For a buffer, the HendersonβHasselbalch equation is .
π The HendersonβHasselbalch equation is valid only for a buffer with a weak acid/base conjugate pair and substantial amounts of both components, while the ICE-table method can be used for any solution if set up correctly.
Further detail
In a buffer containing CH3COOH and CH3COO-, the common-ion effect decreases the percent ionization of CH3COOH when substantial CH3COO- is present.
Because ionization is negligible in the buffer, the CH3COOH and CH3COO- concentrations change principally when an external acid or base is added.
Adding 0.025 mol HCl to 1.0 L containing 0.100 M CH3COOH and 0.100 M CH3COO- converts 0.025 mol CH3COO- to CH3COOH, leaving 0.125 M CH3COOH and 0.075 M CH3COO-.
π Formula - For the resulting acetate buffer, and the ICE calculation gives , so .
π For a buffer based on a weak base such as NH3 and its conjugate acid NH4+, the HendersonβHasselbalch equation still calculates pH and uses Ka, not pOH and Kb.
π Formula - Using for the resulting ammonia mixture gives and .
β Must-know
π Formula - The stated buffer range is approximately .
π A buffer remains effective only until HA or A- is depleted, and its capacity increases as the absolute concentrations of both conjugate components increase.
Further detail
A buffer is most effective when because the conjugate acid and base concentrations are equal.
To select a buffer for a desired pH, choose the candidate whose pKa, calculated as , is closest to that pH.
β Must-know
π Formula - After adding 20.00 mL of 0.100 M NaOH to 50.00 mL of 0.100 M HCl, 0.0030 mol of HβOβΊ remain in 0.070 L, giving and pH 1.37.
π Formula - After adding 75.00 mL of 0.100 M NaOH to 50.00 mL of 0.100 M HCl, 0.0025 mol of OHβ» remain in 0.125 L, giving , pOH 1.70, and pH 12.3.
Further detail
Comparing the moles identified at the equivalence point with the analyte's total volume determines the analyte concentration.
A titration can be monitored by measuring analyte pH as titrant is added or by using an indicator.
At the initial point of a strong-acid titration with 50.00 mL of 0.100 M HCl and no titrant added, [H3O+] is 0.100 M and pH is 1.00.
π Formula - The initial H3O+ amount in 50.00 mL of 0.100 M HCl is .
Before equivalence, excess acid keeps pH below 7; after equivalence, excess base raises it above 7.
β Must-know
π During strong-base titration with strong acid, pH remains above 7 before equivalence, equals 7 at equivalence, and falls below 7 after equivalence.
π At the equivalence point of a strong-acid/strong-base titration, the solution contains water and a neutral salt, so pH is 7.0.
Further detail
π Far past the equivalence point, the pH approaches the pH of the titrant solution because the titrant eventually remains in solution in excess.
β Must-know
π Formula - In the weak-acid buffer region, \mathrm{pH} = \mathrm{p}K_a + \log\left(\frac{[\mathrm{A^-}]}{[\mathrm{HA}]\right).
π At equivalence in a weak-acid/strong-base titration, HA has been converted to its conjugate base Aβ», which makes the solution basic and gives pH greater than 7.
Further detail
Before base is added to a weak acid, calculate the solution pH using an ICE table and the acid dissociation constant Ka.
At weak-acid equivalence, calculate pH using an ICE table for Aβ» reacting with water and Kb, using the actual Aβ» concentration rather than the initial HA concentration.
After equivalence in a weak-acid/strong-base titration, subtract initial HA moles from added OHβ» moles, divide the excess OHβ» by total volume, and convert pOH to pH; far past equivalence, pH approaches the titrant pH.
π Formula - In the weak-base buffer region, \mathrm{pH} = \mathrm{p}K_a + \log\left(\frac{[\mathrm{B}]}{[\mathrm{BH^+}]\right).
Initial solution β buffer β half-equivalence β equivalence β excess titrant.
β Must-know
π The best indicator for a titration changes color at the equivalence-point pH, which should equal the indicatorβs pKa.
Further detail
π Formula - An indicatorβs acid form dissociates according to
Take a 11-question practice quiz on Buffers and Acid-Base Titrations, with every answer explained.
1. When a small amount of acid or base is added to a solution and its pH changes very little, what property does this demonstrate?
2. A patient's blood pH is measured as 7.34. How should this value be classified relative to the stated range for human blood?
Memorize the key concepts of Buffers and Acid-Base Titrations with 10 flashcards.
What does a buffer do to changes in pH?
It resists them by neutralizing added HβΊ or OHβ».
What components form an aqueous buffer?
A weak acid/base conjugate pair, with substantial amounts of both components.
How does substantial acetate affect the ionization of acetic acid in a buffer?
It decreases the percent ionization of acetic acid.
Upload your class notes and Revizly writes a study guide, a quiz and flashcards in about a minute.
Study guide maker