Buffers and Acid-Base Titrations Practice Quiz (11 questions)

All questions and answers

1. When a small amount of acid or base is added to a solution and its pH changes very little, what property does this demonstrate?

It resists pH change by neutralizing added H+ or OH-
It prevents added acid or base from reacting with any component
It makes the solution acidic by releasing H+ when disturbed
It keeps the solution at a neutral pH regardless of additions

It resists pH change by neutralizing added H+ or OH-

Explanation

A buffer limits pH changes by neutralizing added H+ or OH-. pH neutrality confuses resistance with a particular pH, preventing all reactions overstates the effect, and releasing H+ alone describes only one possible response.

2. A patient's blood pH is measured as 7.34. How should this value be classified relative to the stated range for human blood?

Outside the range only if it exceeds 7.42
Outside the required range and described as fatal
Within the required range near its lower boundary
Within the required range near its upper boundary

Outside the required range and described as fatal

Explanation

The required blood pH range is 7.36 to 7.42, so 7.34 is outside it and is described as fatal in the lecture. Treating 7.34 as within the range misplaces the lower boundary; the upper-boundary choices misclassify the value's position or direction.

3. A student adds a measured amount of strong acid to a buffer and wants to track how the conjugate acid and base amounts change as the acid reacts. Which table should the student use for this step?

A common-ion comparison
A neutralization table
An ICE table
A Henderson–Hasselbalch calculation

A neutralization table

Explanation

A neutralization table tracks the reaction with added acid or base and the resulting conjugate-component amounts. An ICE table tracks equilibrium changes; Henderson–Hasselbalch calculates buffer pH, while a common-ion comparison addresses ionization.

4. A student is given a solution that lacks substantial amounts of both members of a weak-acid/conjugate-base pair. Which method choice is justified for calculating its pH?

Use Henderson–Hasselbalch because any weak acid qualifies as a buffer
Use a correctly set-up ICE table; Henderson–Hasselbalch is not valid here
Use neither method because the solution lacks a substantial conjugate pair
Use Henderson–Hasselbalch after treating the missing component as substantial

Use a correctly set-up ICE table; Henderson–Hasselbalch is not valid here

Explanation

Henderson–Hasselbalch requires a buffer with a weak-acid/base conjugate pair and substantial amounts of both components, whereas a correctly set-up ICE method can be used for any solution. Treating any weak acid as a buffer ignores the pair requirement, and restricting ICE tables to buffers reverses the method distinction.

5. What does buffer capacity describe?

The pKa value closest to the pH a buffer is intended to maintain
The pH at which a buffer contains equal concentrations of acid and conjugate base
The pH interval in which a buffer's conjugate pair remains effective
The amount of acid or base a buffer can absorb before its pH changes substantially

The amount of acid or base a buffer can absorb before its pH changes substantially

Explanation

Buffer capacity describes how much added acid or base a buffer can tolerate without a substantial pH change, and it increases with the absolute concentrations of both components. The pH interval of effectiveness describes buffer range, not capacity.

6. At the equivalence point, 50.00 mL of 0.100 M HCl has reacted with what volume of 0.100 M NaOH?

100.00 mL
75.00 mL
50.00 mL
20.00 mL

50.00 mL

Explanation

Equal concentrations require equal volumes to provide equal moles of acid and base, so 50.00 mL of NaOH reaches equivalence. Adding 75.00 mL would pass the equivalence point and leave excess hydroxide.

7. What is the purpose of calculating the excess hydronium or hydroxide after a titrant is added during a strong-acid/strong-base titration?

To calculate the equivalence-point volume from the total solution volume
To determine the solution’s pH from the reagent remaining after neutralization
To estimate the titrant’s concentration from the salt produced in solution
To identify the analyte by comparing its initial color with the titrant

To determine the solution’s pH from the reagent remaining after neutralization

Explanation

Neutralization consumes the limiting reagent, so the remaining excess acid or base determines the solution’s pH after accounting for total volume. Calculating the equivalence-point volume instead requires finding when the acid and base have reacted in equal amounts.

8. How does the pH at equivalence differ between a weak-acid/strong-base titration and a strong-acid/strong-base titration?

It is 7 in the weak-acid titration but above 7 in the strong-acid titration.
It is 7 in both titrations because the acid and base have reacted completely.
It is above 7 in the weak-acid titration but 7 in the strong-acid titration.
It is below 7 in the weak-acid titration but 7 in the strong-acid titration.

It is above 7 in the weak-acid titration but 7 in the strong-acid titration.

Explanation

At weak-acid equivalence, the acid has been converted to its conjugate base, which makes the solution basic; strong-acid/strong-base equivalence leaves a neutral salt and water. The claim that both equivalence points are neutral overlooks the basic behavior of the weak acid’s conjugate base.

9. Why do polyprotic acid titration curves show buffer-region points at pH = pKa₁ and pH = pKa₂?

Each point marks a stage where the corresponding acid-base conjugate pair buffers the solution.
Each point marks an equivalence point where all acidic protons have been neutralized.
Each point marks the moment when the acid concentration becomes equal to the titrant concentration.
Each point marks a sharp pH jump caused by complete dissociation of the acid.

Each point marks a stage where the corresponding acid-base conjugate pair buffers the solution.

Explanation

At buffer-region points, the relevant conjugate acid and base forms are present in balanced amounts, so the pH equals the corresponding pKa. Equivalence points instead indicate stoichiometric neutralization, not the buffer-region relationship.

10. When choosing an indicator for a titration with a known equivalence-point pH, how should you select the indicator?

Choose one whose pKa is close to the initial solution pH.
Choose one whose acid and base forms have the same color at equivalence.
Choose one whose pKa is close to the equivalence-point pH.
Choose one whose color-change range lies well above the equivalence-point pH.

Choose one whose pKa is close to the equivalence-point pH.

Explanation

An indicator is best suited when its pKa matches the equivalence-point pH, placing its color transition near that point. Matching the initial pH would not ensure the color changes near equivalence.

11. Which pair of components characterizes the main buffer system in human blood?

Hydrochloric acid and chloride
Phosphoric acid and phosphate
Carbonic acid and bicarbonate
Ammonia and ammonium

Carbonic acid and bicarbonate

Explanation

The main blood buffer consists of the weak acid carbonic acid and its conjugate base, bicarbonate. Ammonia and ammonium can form a buffer pair, but they are not identified as the main blood buffer system.

Study with flashcards

Lock in the answers with 10 flashcards on Buffers and Acid-Base Titrations.

What does a buffer do to changes in pH?

It resists them by neutralizing added H⁺ or OH⁻.

What components form an aqueous buffer?

A weak acid/base conjugate pair, with substantial amounts of both components.

How does substantial acetate affect the ionization of acetic acid in a buffer?

It decreases the percent ionization of acetic acid.

See the flashcards →

Read the study guide

Go over the full study guide for Buffers and Acid-Base Titrations.

Read the study guide →

Related classes

Make your own practice quizzes

Upload your class notes and Revizly writes a practice quiz with explained answers in about a minute.

Quiz maker