Diode Applications Flashcards (67 cards)

All cards

1Question

What does half-wave rectification do to an input signal?

Answer

It removes one half of the signal to establish a DC level.

2Question

When does an ideal half-wave rectifier’s diode conduct during a cycle?

Answer

During the positive half-cycle, from t=0t=0 to t=T/2t=T/2.

3Question

What is the ideal sinusoidal half-wave rectifier’s average output voltage?

Answer

Vdc=0.318Vm=Vm/πV_{dc}=0.318V_m=V_m/\pi.

4Question

What is peak inverse voltage (PIV) for a rectifier diode?

Answer

The maximum reverse-bias voltage the diode can withstand without entering the Zener avalanche region.

5Question

What is another name for peak inverse voltage (PIV)?

Answer

Peak reverse voltage (PRV).

6Question

During a bridge rectifier’s positive half-cycle, which diodes conduct?

Answer

D2 and D3 conduct.

7Question

During a bridge rectifier’s negative half-cycle, which diodes conduct?

Answer

D1 and D4 conduct.

8Question

What is the average output voltage of an ideal bridge full-wave rectifier?

Answer

Vdc=0.636VmV_{dc}=0.636V_m

9Question

How does an ideal bridge full-wave average compare with the ideal half-wave average?

Answer

It is twice the ideal half-wave average.

10Question

Which diode conducts during the positive primary half-cycle in a center-tapped full-wave rectifier?

Answer

D1 conducts.

11Question

What happens to D1 and D2 during the negative primary half-cycle?

Answer

Their roles interchange.

12Question

What remains unchanged in polarity across the load during both half-cycles?

Answer

The load polarity.

13Question

In Example 2.17, what output peak does the voltage divider produce from a 10 V input peak?

Answer

5 V.

14Question

In Example 2.17, what is the full-wave output average?

Answer

3.18 V.

15Question

What does a clipper do to an input signal?

Answer

It removes part of the signal without distorting the remaining waveform.

16Question

Where is the diode placed in a series clipper?

Answer

In series with the load.

17Question

Where is the diode placed in a parallel clipper?

Answer

In a branch parallel to the load.

18Question

What steps are used to analyze a clipper circuit?

Answer

Locate the output voltage, assess supply polarity’s effect on diode bias, find the input transition voltage, and plot input and output on matching scales.

19Question

When does the diode turn on in a series-source clipper?

Answer

When the input exceeds the DC source voltage.

20Question

What is the transition condition in a series-source clipper?

Answer

The input equals the DC source voltage.

21Question

What is the output voltage when the diode is on in a series-source clipper?

Answer

vo=vi−Vv_o = v_i - V

22Question

What is the output voltage when the diode is off in a series-source clipper?

Answer

0 V.

23Question

What is the diode current when the diode is off in a series-source clipper?

Answer

Zero.

24Question

In Example 2.18, what is the output below an input of -5 V?

Answer

0 V.

25Question

In Example 2.18, what is the output equation when the diode is on?

Answer

vo=vi+5 Vv_o = v_i + 5\text{ V}.

26Question

In Example 2.20, what is the output when the diode is on and vi≤4 Vv_i \le 4\text{ V}?

Answer

4 V.

27Question

In Example 2.20, what is the output when the diode is off and vi≥4 Vv_i \ge 4\text{ V}?

Answer

vo=viv_o = v_i.

28Question

What components form a clamper network?

Answer

A diode, resistor, and capacitor.

29Question

What does a clamper do to a waveform?

Answer

It shifts the waveform to a different DC level without changing its appearance.

30Question

What is the clamper time-constant formula?

Answer

τ=RC\tau = RC

31Question

What must the clamper time constant prevent during diode non-conduction?

Answer

Significant capacitor discharge.

32Question

Which input interval begins clamper analysis?

Answer

The interval that forward-biases the diode.

33Question

What capacitor behavior does clamper analysis assume while the diode is on?

Answer

The capacitor charges instantaneously.

34Question

In Example 2.22, what is the output during the diode-on interval?

Answer

5 V.

35Question

In Example 2.22, what is the capacitor voltage during the diode-on interval?

Answer

25 V.

36Question

In Example 2.22, what is the output during the diode-off interval?

Answer

35 V.

37Question

When does a silicon diode with a 0.7 V threshold remain off?

Answer

When the input is below 0.7 V.

38Question

What is the half-wave output average when the sinusoidal peak greatly exceeds the silicon threshold?

Answer

Vdc=0.318(Vm−VK)V_{dc}=0.318(V_m-V_K).

39Question

What does a negative average output indicate in a negative half-wave rectifier?

Answer

Its polarity is opposite to the defined output polarity.

40Question

What is the ideal average output for a negative half-wave rectifier with a 20 V peak input?

Answer

−6.36 V.

41Question

What is the silicon-diode average output for a negative half-wave rectifier with a 20 V peak input?

Answer

−6.14 V.

42Question

How many silicon diodes conduct in a bridge rectifier’s current path?

Answer

Two diodes conduct.

43Question

What is the load-voltage formula for a silicon bridge rectifier?

Answer

vo=vi−2VKv_o=v_i-2V_K

44Question

What is the silicon bridge average when the sinusoidal peak greatly exceeds twice the diode threshold?

Answer

Vdc=0.636(Vm−2VK)V_{dc}=0.636(V_m-2V_K)

45Question

What minimum PIV rating must each diode in a full-wave bridge rectifier have?

Answer

At least the input peak voltage, PIV≥VmPIV\geq V_m.

46Question

What does a center-tapped transformer divide its secondary winding into?

Answer

Two halves.

47Question

What does the center tap provide for the two secondary voltages?

Answer

A reference point.

48Question

What output does a center-tapped full-wave rectifier produce compared with a bridge rectifier?

Answer

The same output polarity and DC levels.

49Question

What is the diode PIV requirement for a center-tapped rectifier?

Answer

PIV≥2VmPIV\geq 2V_m.

50Question

What two contributions make up the center-tapped rectifier diode PIV?

Answer

The secondary peak and load peak, each VmV_m.

51Question

In Example 2.17, what is each diode’s peak inverse voltage?

Answer

5 V.

52Question

How does Example 2.17’s diode PIV compare with that of a half-wave rectifier using the same input?

Answer

It is half as large.

53Question

What determines the minimum input voltage needed to turn on a reverse-biased diode in a biased clipper?

Answer

The DC supply polarity.

54Question

How can the DC supply affect source voltage in a biased clipper?

Answer

It can aid or oppose the source voltage.

55Question

What is the output peak in a series-source clipper?

Answer

Vopeak=Vm−VV_{o\text{peak}} = V_m - V

56Question

What does VmV_m represent in the series-source clipper output-peak formula?

Answer

The maximum peak voltage of the input AC signal.

57Question

In Example 2.19, what output occurs during the 20 V input from 0→T/20 \to T/2?

Answer

25 V.

58Question

In Example 2.19, what output occurs during the -10 V input from T/2→TT/2 \to T?

Answer

0 V.

59Question

In Example 2.21, what transition voltage does the silicon diode produce in the 4-V clipper?

Answer

3.3 V.

60Question

In Example 2.21, what is the output for inputs less than 3.3 V?

Answer

3.3 V.

61Question

In clamper analysis, how many time constants are assumed for full capacitor charging or discharging?

Answer

Five time constants.

62Question

What does a charged capacitor do when the clamper diode is off?

Answer

It acts as a DC source that shifts the input waveform.

63Question

In Example 2.22, what is the period of the 1000-Hz input?

Answer

1 ms.

64Question

In Example 2.22, what is the output swing?

Answer

30 V.

65Question

In Example 2.23, what is the silicon-diode on-state output?

Answer

4.3 V.

66Question

In Example 2.23, how do the input and output waveform swings compare?

Answer

They have the same swing.

67Question

In Example 2.22, what is the discharging network’s time constant?

Answer

10 s.

Test yourself with the quiz

Answer 22 questions on Diode Applications.

1. An ideal diode is connected in a half-wave rectifier to a sinusoidal source. What output appears during the interval from t=T/2t=T/2 to t=Tt=T?

2. An ideal sinusoidal half-wave rectifier has an input peak voltage of 20 V20\text{ V}. What is its average output voltage?

Take the quiz →

Read the study guide

Go over the full study guide for Diode Applications.

Read the study guide →

Related classes

Make your own flashcards

Upload your class notes and Revizly writes your flashcards in about a minute.

Flashcard maker