Diode Applications Practice Quiz (22 questions)

All questions and answers

1. An ideal diode is connected in a half-wave rectifier to a sinusoidal source. What output appears during the interval from t=T/2t=T/2 to t=Tt=T?

The positive half-cycle, repeated at the output
The negative half-cycle, reproduced at the output
A constant voltage equal to the input peak
Zero volts, because the diode is off

Zero volts, because the diode is off

Explanation

In an ideal half-wave rectifier, the diode turns off during the negative half-cycle, so the output is zero. Reproducing or reversing the negative input confuses the blocking behavior with conduction.

2. An ideal sinusoidal half-wave rectifier has an input peak voltage of 20 V20\text{ V}. What is its average output voltage?

Approximately 12.73 V12.73\text{ V}
Approximately 6.36 V6.36\text{ V}
Approximately 20 V20\text{ V}
Approximately 10 V10\text{ V}

Approximately $$6.36\text{ V}$$

Explanation

For an ideal sinusoidal half-wave rectifier, Vdc=0.318VmV_{dc}=0.318V_m, so 0.318×20 V=6.36 V0.318\times20\text{ V}=6.36\text{ V}. Using the peak itself, the full-wave factor, or half the peak applies a different quantity or rule.

3. What does half-wave rectification do to an input signal to establish a DC level?

Reverses the polarity of each half-cycle
Amplifies one half-cycle and preserves the other
Removes one half of the input signal
Smooths both halves into a constant signal

Removes one half of the input signal

Explanation

Half-wave rectification removes one half of the input signal to establish a DC level. Smoothing, polarity reversal, and amplification describe different operations.

4. A designer selects a rectifier diode for a half-wave circuit with source peak voltage VmV_m. Which rating must be sufficient to prevent reverse-bias breakdown?

A forward current rating numerically equal to VmV_m
An average output voltage rating at least 0.318Vm0.318V_m
A forward voltage drop rating at least VmV_m
A peak inverse voltage rating at least VmV_m

A peak inverse voltage rating at least $$V_m$$

Explanation

The diode's peak inverse voltage (PIV), also called peak reverse voltage (PRV), is its maximum reverse-bias voltage rating; for a half-wave rectifier it must be at least VmV_m. The forward drop is a conducting voltage, while average output and forward current do not specify the reverse-voltage limit.

5. In a bridge rectifier, D2 and D3 conduct during the positive half-cycle. Which pair conducts during the negative half-cycle so the load polarity remains unchanged?

D2 and D3
D1 and D4
D1 and D3
D2 and D4

D1 and D4

Explanation

During the negative half-cycle, D1 and D4 conduct while D2 and D3 are off, preserving the load polarity. D2 and D3 repeats the positive-half-cycle path; D1 and D3 and D2 and D4 each use a mixed pair that does not match the bridge conduction sequence.

6. An ideal bridge full-wave rectifier has a sinusoidal input peak of Vm=20 VV_m=20\text{ V}. What is its average output voltage?

25.44 V25.44\text{ V}
20 V20\text{ V}
6.36 V6.36\text{ V}
12.72 V12.72\text{ V}

$$12.72\text{ V}$$

Explanation

The ideal bridge average is Vdc=0.636VmV_{dc}=0.636V_m, so 0.636×20=12.72 V0.636\times20=12.72\text{ V}. The half-wave factor gives 6.36 V, doubling the full-wave result gives 25.44 V, and 20 V is the peak rather than the average.

7. In a center-tapped full-wave rectifier, D1 conducts and D2 is off during the positive primary half-cycle. What happens during the negative primary half-cycle?

Both diodes conduct, and load polarity stays the same
D1 conducts, D2 is off, and load polarity stays the same
D2 conducts, D1 is off, and load polarity reverses
D2 conducts, D1 is off, and load polarity stays the same

D2 conducts, D1 is off, and load polarity stays the same

Explanation

The diode roles interchange on the negative half-cycle: D2 conducts and D1 is off, while the load polarity remains the same. Retaining D1's conduction misses the interchange; simultaneous conduction and reversed load polarity contradict the stated operation.

8. A center-tapped rectifier has a secondary peak and load peak each equal to Vm=18 VV_m=18\text{ V}. What minimum diode peak inverse voltage rating is required?

At least 18 V18\text{ V}
At least 9 V9\text{ V}
At least 54 V54\text{ V}
At least 36 V36\text{ V}

At least $$36\text{ V}$$

Explanation

For a center-tapped rectifier, the PIV requirement is PIV≥2VmPIV\geq2V_m because the secondary peak and load peak each contribute VmV_m; thus 2×18=36 V2\times18=36\text{ V}. The 18 V value reflects the bridge requirement or counts one contribution, while 9 V halves the required value and 54 V adds an unsupported extra contribution.

9. In a full-wave rectifier network, a voltage divider reduces a 10 V input peak to 5 V at the rectifier input. What average DC output results using Vdc=0.636VpeakV_{dc}=0.636V_{peak}?

6.36 V
5.00 V
3.18 V
1.59 V

3.18 V

Explanation

The divider gives a 5 V peak, so Vdc=0.636×5 V=3.18 VV_{dc}=0.636\times5\text{ V}=3.18\text{ V}. The 6.36 V choice uses the original 10 V peak, 1.59 V applies half the full-wave coefficient, and 5.00 V confuses peak voltage with average voltage.

10. A diode in the full-wave rectifier example has a peak inverse voltage (PIV) of 5 V. For the same input, what comparison with the PIV of a half-wave rectifier follows?

It is equal to the half-wave rectifier's PIV requirement.
It is half the half-wave rectifier's PIV requirement.
It equals the full-wave rectifier's 3.18 V average output.
It is twice the half-wave rectifier's PIV requirement.

It is half the half-wave rectifier's PIV requirement.

Explanation

For the same input, the example's 5 V diode PIV is half the PIV required by a half-wave rectifier. Equal or double reverses the stated comparison, while 3.18 V is an average output value, not a PIV comparison.

11. A diode network removes part of an input signal while leaving the remaining waveform undistorted. What is this network called?

A rectifier
A clipper
A limiter that reshapes the remaining waveform
An amplifier

A clipper

Explanation

A clipper removes a portion of an input signal without distorting the waveform that remains. A rectifier changes signal polarity behavior, an amplifier changes signal magnitude, and reshaping the remainder is not the defining feature of clipping.

12. A circuit's diode is connected in a separate branch across the load rather than along the load's current path. Which clipper configuration is it?

A full-wave rectifier
A series clipper
A parallel clipper
A biased clipper

A parallel clipper

Explanation

A parallel clipper places the diode in a branch parallel to the load. A series clipper places the diode in series with the load; bias describes a supply arrangement, while a full-wave rectifier is a different circuit function.

13. While analyzing a clipper, an engineer must determine its output waveform. Which sequence follows the standard analysis procedure?

Assess supply polarity, plot the output, locate the output, then find the transition voltage
Locate the output, find the transition voltage, plot the waveforms, then assess supply polarity
Find the transition voltage, locate the output, plot both waveforms, then assess supply polarity
Locate the output, assess supply polarity and diode bias, find the transition voltage, then plot input and output on matching scales

Locate the output, assess supply polarity and diode bias, find the transition voltage, then plot input and output on matching scales

Explanation

Clipper analysis proceeds by identifying where the output is defined, considering how the DC supply affects diode bias, finding the switching threshold, and plotting input and output on the same scales. The other sequences place waveform plotting or the polarity assessment at the wrong stage.

14. In a series-source clipper, the DC source is 6 V and the input rises from 0 V. At what input condition does the diode turn on?

When the input exceeds 0 V
When the input is below 6 V
When the input exceeds 6 V
When the input reaches -6 V

When the input exceeds 6 V

Explanation

The diode is off at zero input, transitions when the input equals the DC source voltage, and turns on when the input exceeds that voltage. Conduction at zero or below the threshold misapplies the specified bias condition, while -6 V reverses the threshold polarity.

15. A series-source clipper has a 3 V DC source and an input of 5 V, so its diode is on. Using the ideal-diode model, what output voltage results?

2 V
8 V
5 V
0 V

2 V

Explanation

When the diode is on, its ideal equivalent is a short and the output is vo=vi−Vv_o=v_i-V, giving 5−3=2 V5-3=2\text{ V}. A zero output belongs to the off state, adding the source uses the wrong relation, and 5 V omits the source drop.

16. In the clipper of Example 2.18, the input is -7 V, below the -5 V transition. What is the output?

-2 V
7 V
-5 V
0 V

0 V

Explanation

Below -5 V, the diode is open and the output is 0 V; the relation vo=vi+5 Vv_o=v_i+5\text{ V} applies in the on state. The -2 V result incorrectly extends that on-state equation, while -5 V confuses the threshold with the output.

17. In the 4-V clipper of Example 2.20, what output is measured when the input is 2 V?

2 V
0 V
-2 V
4 V

4 V

Explanation

For inputs at or below 4 V, the diode is on and the output measured across the supply-diode series combination is 4 V. The input-following relation applies at or above the transition, while subtracting the supply confuses this output definition with another clipper relation.

18. A circuit shifts an input waveform to a new DC level while preserving its shape. Which circuit function does this describe?

Rectification
Amplification
Clamping
Clipping

Clamping

Explanation

A clamper shifts a waveform to a different DC level without changing its appearance. Rectification changes the waveform into a unidirectional form, amplification changes its magnitude, and clipping limits portions of it.

19. A clamper uses a resistor of 200 kΩ200\,\text{k}\Omega and a capacitor of 0.05 mF0.05\,\text{mF}. What is its time constant, and what design goal should it meet?

10 s10\,\text{s}, small enough to discharge the capacitor while the diode is off
10 s10\,\text{s}, large enough to limit capacitor discharge while the diode is off
0.1 s0.1\,\text{s}, large enough to limit capacitor discharge while the diode is off
0.1 s0.1\,\text{s}, small enough to discharge the capacitor while the diode is off

$$10\,\text{s}$$, large enough to limit capacitor discharge while the diode is off

Explanation

Using τ=RC\tau=RC gives (200×103)(0.05×10−3)=10 s(200\times10^3)(0.05\times10^{-3})=10\,\text{s}. A sufficiently large time constant prevents significant capacitor discharge while the diode is non-conducting; the reciprocal-product errors produce 0.1 s0.1\,\text{s}, while the small-time-constant choices reverse the design goal.

20. When analyzing a clamper, an engineer has identified the input interval that forward-biases the diode. What should the engineer do next under the standard analysis assumptions?

Check that the output swing matches the input before tracking output polarity
Assume the capacitor holds its prior voltage until the diode turns off
Treat the diode as off and calculate the capacitor’s discharge during this interval
Assume the capacitor charges instantaneously to a level set by the surrounding network

Assume the capacitor charges instantaneously to a level set by the surrounding network

Explanation

During the diode-on interval, clamper analysis assumes the capacitor charges instantaneously to a voltage determined by the surrounding network; the off-state assumption is that it holds its voltage. Tracking the defined output polarity and checking matching input and output swings are later parts of the analysis.

21. In Example 2.22, the diode-on interval produces an output of 5 V5\,\text{V} and charges the capacitor to 25 V25\,\text{V}. What output occurs during the diode-off interval?

−20 V-20\,\text{V}
5 V5\,\text{V}
25 V25\,\text{V}
35 V35\,\text{V}

$$35\,\text{V}$$

Explanation

With the diode off, the capacitor’s stored voltage shifts the input, and the example’s circuit analysis gives an output of 35 V35\,\text{V}. The values 25 V25\,\text{V} and 5 V5\,\text{V} are the capacitor voltage and diode-on output, while −20 V-20\,\text{V} results from incorrectly subtracting those values.

22. In Example 2.22, the diode-off interval lasts 0.5 ms0.5\,\text{ms}, while five time constants equal 50 ms50\,\text{ms}. What conclusion follows for the capacitor and output swing?

The capacitor fully discharges, and the output swing is 30 V30\,\text{V}
The capacitor fully discharges, and the output swing is 5 V5\,\text{V}
The capacitor holds its voltage, and the output swing is 25 V25\,\text{V}
The capacitor holds its voltage, and the output swing is 30 V30\,\text{V}

The capacitor holds its voltage, and the output swing is $$30\,\text{V}$$

Explanation

Because 0.5 ms0.5\,\text{ms} is much shorter than the 50 ms50\,\text{ms} five-time-constant discharge period, the capacitor holds its voltage and the output swing is 30 V30\,\text{V}. Full discharge misapplies the five-time-constant assumption, and 25 V25\,\text{V} confuses stored capacitor voltage with output swing.

Study with flashcards

Lock in the answers with 67 flashcards on Diode Applications.

What does half-wave rectification do to an input signal?

It removes one half of the signal to establish a DC level.

When does an ideal half-wave rectifier’s diode conduct during a cycle?

During the positive half-cycle, from t=0t=0 to t=T/2t=T/2.

What is the ideal sinusoidal half-wave rectifier’s average output voltage?

Vdc=0.318Vm=Vm/πV_{dc}=0.318V_m=V_m/\pi.

See the flashcards →

Read the study guide

Go over the full study guide for Diode Applications.

Read the study guide →

Related classes

Make your own practice quizzes

Upload your class notes and Revizly writes a practice quiz with explained answers in about a minute.

Quiz maker