★ Must-know
📐 Formula - For an ideal sinusoidal half-wave rectifier, the average output is .
Further detail
📐 Formula - When the sinusoidal peak is sufficiently greater than the silicon diode threshold, the half-wave output average is .
When the diode is oriented to conduct on the negative half-cycle, the output average is negative, indicating polarity opposite to the defined output polarity.
For a negative half-wave rectifier with peak input 20 V, the ideal output average is −6.36 V and the silicon-diode output average is −6.14 V, a difference of 0.22 V.
The positive half-cycle passes; the negative half-cycle is blocked.
★ Must-know
📐 Formula - For an ideal bridge full-wave rectifier, the average output is , twice the ideal half-wave average.
Further detail
📐 Formula - When the sinusoidal peak is much greater than twice the diode threshold, the silicon bridge average is .
📌 Each diode in a full-wave bridge rectifier must have a PIV rating of at least the input peak voltage, .
★ Must-know
Further detail
A center-tapped transformer divides its secondary winding into two halves and provides a reference point for the two secondary voltages.
A center-tapped full-wave rectifier produces the same output polarity and DC levels as a bridge full-wave rectifier.
📐 Formula - The center-tapped rectifier diode PIV requirement is , where the secondary peak and the load peak each contribute .
The bridge uses four diodes; the center-tapped circuit uses two.
★ Must-know
Further detail
★ Must-know
📌 A series clipper places the diode in series with the load, whereas a parallel clipper places the diode in a branch parallel to the load.
Further detail
★ Must-know
📌 In the series-source clipper, the diode is off at zero input; the transition occurs when the input equals the DC source voltage, and the diode turns on when the input exceeds that voltage.
📌 For the series-source clipper, the diode-on equivalent is a short circuit and the output is ; with the diode off, the diode current is zero and the output is 0 V.
Further detail
Locate the output, assess polarity, find the transition, then plot.
★ Must-know
📌 In Example 2.18, the diode turns off when the negative input reaches -5 V; below -5 V the output is 0 V, while in the on state the output is .
📌 In Example 2.20, the output is measured across the series combination of the 4-V supply and diode: when the diode is on, the output is 4 V for , and when it is off, the output is for .
Further detail
In Example 2.19, for a square-wave input of 20 V during , the diode conducts and the output is 25 V; for an input of -10 V during , the diode is open and the output is 0 V.
In Example 2.21, a silicon diode with shifts the transition voltage in the 4-V clipper from 4 V to 3.3 V.
📌 In Example 2.21, the diode is open and for inputs greater than 3.3 V, while for inputs less than 3.3 V it is on and the output is 3.3 V.
★ Must-know
📐 Formula - The clamper time constant is and must be sufficiently large to prevent significant capacitor discharge while the diode is non-conducting.
Further detail
The clamper analysis assumes that the capacitor fully charges or discharges in five time constants.
When the diode is on, the capacitor charges to a voltage determined by the surrounding network; when the diode is off, the charged capacitor acts as a DC source that shifts the input waveform.
Forward-bias, charge, hold, check the output polarity and swing.
★ Must-know
Further detail
📐 Formula - In Example 2.22, the discharging network has , so five time constants equal 50 s.
In Example 2.22, the 0.5-ms diode-off interval is shorter than the 50-ms five-time-constant discharge period, so the capacitor holds its voltage and the output swing is 30 V.
In Example 2.23, using a silicon diode with gives an on-state output of 4.3 V, a capacitor voltage of 24.3 V, and an off-state output of 34.3 V.
In Example 2.23, the input and output waveforms have the same swing.
Take a 22-question practice quiz on Diode Applications, with every answer explained.
1. An ideal diode is connected in a half-wave rectifier to a sinusoidal source. What output appears during the interval from to ?
2. An ideal sinusoidal half-wave rectifier has an input peak voltage of . What is its average output voltage?
Memorize the key concepts of Diode Applications with 67 flashcards.
What does half-wave rectification do to an input signal?
It removes one half of the signal to establish a DC level.
When does an ideal half-wave rectifier’s diode conduct during a cycle?
During the positive half-cycle, from to .
What is the ideal sinusoidal half-wave rectifier’s average output voltage?
.
Upload your class notes and Revizly writes a study guide, a quiz and flashcards in about a minute.
Study guide maker