Heat Engine Fundamentals Flashcards (78 cards)

All cards

1Question

What does a heat engine convert part of combustion heat into?

Answer

Mechanical work.

2Question

Where does fuel burn in an external-combustion engine?

Answer

Outside the engine working space.

3Question

How does heat reach the working fluid in an external-combustion engine?

Answer

It crosses a boundary to reach the working fluid.

4Question

Where does fuel burn in an internal-combustion engine?

Answer

Inside the engine working space.

5Question

What changes in the working fluid during an engine cycle?

Answer

Its thermodynamic state and composition change.

6Question

What three functional groups make up engine elements?

Answer

The engine group, auxiliary systems, and surveillance and control equipment.

7Question

What does the engine group contain?

Answer

The fixed structure and the moving mechanism that transmits mechanical work.

8Question

Which parts are the main fixed parts of an engine?

Answer

The cylinder head, intake and exhaust manifolds, cylinder block, upper crankcase, and lower crankcase or oil pan.

9Question

How does the moving mechanism convert piston motion into crankshaft rotation?

Answer

It transmits cylinder-pressure force through the piston, piston pin, connecting rod, and crank throw to the crankshaft.

10Question

What does the crankshaft deliver to the flywheel?

Answer

Torque.

11Question

What is the piston position at Top Dead Centre (TDC)?

Answer

The upper extreme position.

12Question

What is the piston position at Bottom Dead Centre (BDC)?

Answer

The lower extreme position.

13Question

What is the compression ratio formula using maximum and clearance volumes?

Answer

ε=VAVC\varepsilon = \frac{V_A}{V_C}

14Question

What is the swept-volume formula for one cylinder with bore DD and stroke SS?

Answer

VS=πD24SV_S = \frac{\pi D^2}{4}S

15Question

How is total engine displacement calculated from cylinder count and swept volume?

Answer

Vt=iVSV_t = iV_S

16Question

What does the fuel system meter and deliver?

Answer

The required fuel quantity.

17Question

What does the cooling system limit?

Answer

Component temperature.

18Question

What do torque meters measure?

Answer

Engine torque.

19Question

What does combustion release into the engine’s working fluid?

Answer

Heat.

20Question

What forces the engine piston?

Answer

Cylinder pressure.

21Question

How do the engine’s moving parts convert piston motion?

Answer

They convert reciprocating motion into crankshaft rotation.

22Question

How does a spark-ignition engine initiate combustion?

Answer

An electric spark between spark-plug electrodes.

23Question

How does a compression-ignition engine initiate combustion?

Answer

Fuel self-ignites in highly compressed, hot air.

24Question

What heat-addition processes define the idealized Otto and Diesel cycles?

Answer

Constant-volume heat addition defines the Otto cycle; constant-pressure heat addition defines the Diesel cycle.

25Question

Which criteria classify engines by fuel, mixture preparation, and combustion chamber?

Answer

Fuel state, number of fuels, mixture-preparation place and method, and combustion-chamber compartments.

26Question

Which criteria classify engines by operation and physical configuration?

Answer

Ignition method, working cycle, induction process, cooling method, mean piston speed, cylinder number and arrangement, cylinder-axis position, and crankshaft-axis relation.

27Question

How many piston strokes and crankshaft revolutions complete a four-stroke engine cycle?

Answer

Four piston strokes and two crankshaft revolutions.

28Question

How many crankshaft degrees does a two-stroke engine cycle span?

Answer

360°CA.

29Question

During which four-stroke phase does fresh charge enter as the piston moves toward BDC?

Answer

Intake.

30Question

During which four-stroke phase does the piston move toward TDC with the valves closed?

Answer

Compression.

31Question

When does combustion begin in the four-stroke cycle?

Answer

Near the end of compression.

32Question

During which four-stroke phase do high-pressure gases push the piston toward BDC?

Answer

Expansion.

33Question

During which four-stroke phase does the piston move toward TDC and expel burned gases?

Answer

Exhaust.

34Question

How is cycle frequency νC\nu_C calculated from crankshaft speed nn and strokes per cycle τ\tau?

Answer

νC=n30τ\nu_C = \frac{n}{30\tau} cycles per second.

35Question

How is cycle period TCT_C related to cycle frequency νC\nu_C?

Answer

TC=1νCT_C = \frac{1}{\nu_C} seconds per cycle.

36Question

How is crankshaft angular speed ω\omega calculated from speed nn in rpm?

Answer

ω=πn30\omega = \frac{\pi n}{30} rad/s.

37Question

How is time tt for crank-angle interval α\alpha calculated at speed nn?

Answer

t=α6nt = \frac{\alpha}{6n} s.

38Question

How is mean piston speed WPW_P calculated when stroke SS is in metres?

Answer

WP=Sn30W_P = \frac{Sn}{30} m/s.

39Question

What does a p–α diagram plot, and which valve events does it mark?

Answer

It plots cylinder pressure against crank angle and marks EVC, IVC, EVO, and IVO.

40Question

What do the symbols s, y, and t mark on a p–α diagram?

Answer

Spark discharge or injection onset, maximum cylinder pressure, and end of heat release.

41Question

Where are cylinder volume minimum and maximum, and how does it change between them?

Answer

Volume is minimum at TDC, maximum at BDC, and increases as the piston moves from TDC to BDC.

42Question

How is combustion duration distributed around TDC for well-phased combustion?

Answer

Approximately one third occurs before TDC and two thirds after TDC.

43Question

What kind of process is combustion?

Answer

A high-temperature chemical oxidation process involving fuel and air.

44Question

What bounds the cylinder working space?

Answer

The cylinder head, cylinder liner, and piston crown.

45Question

How does working-fluid pressure produce work during expansion?

Answer

It acts on the piston crown to produce mechanical work.

46Question

What does the cylinder head do?

Answer

It closes the upper part of the cylinder.

47Question

What do the intake and exhaust manifolds do?

Answer

They guide gases into and out of the cylinder.

48Question

What does the cylinder block do?

Answer

It contains and supports the cylinders.

49Question

What does the upper crankcase support?

Answer

The crankshaft region.

50Question

What does the lower crankcase or oil pan do?

Answer

It closes the bottom and stores lubricating oil.

51Question

What do piston rings do in an engine cylinder?

Answer

They seal the cylinder and control oil.

52Question

What does the piston pin connect?

Answer

It connects the piston to the connecting rod.

53Question

What force does the connecting rod transmit between engine components?

Answer

It transmits force between the piston and crank throw.

54Question

How does the connecting rod’s small end move?

Answer

It follows piston motion.

55Question

How does the connecting rod’s big end move?

Answer

It moves around the crankshaft axis.

56Question

How does a multicylinder engine combine assembly torque contributions, and what are its basic cylinder arrangements?

Answer

At the crankshaft; in-line, V, H, and star configurations.

57Question

What distance does a piston stroke measure?

Answer

Piston travel between Top Dead Centre and Bottom Dead Centre.

58Question

What formula relates total cylinder volume, clearance volume, and swept volume?

Answer

VA=VC+VSV_A = V_C + V_S

59Question

What is another name for total engine displacement?

Answer

Engine capacity.

60Question

What does the lubrication system reduce?

Answer

Friction.

61Question

What does the valve timing system control?

Answer

Intake and exhaust events.

62Question

What initiates combustion in spark-ignition engines?

Answer

The ignition system.

63Question

What determines engine power?

Answer

Engine torque and engine speed.

64Question

What does control equipment use to regulate engine operation?

Answer

Measured information.

65Question

What role do fixed engine parts serve?

Answer

They form and support the engine structure.

66Question

Which measurements define an engine’s basic geometry?

Answer

Bore, stroke, and cylinder volumes.

67Question

What do auxiliary engine systems do?

Answer

They support engine operation.

68Question

What do engine surveillance and control equipment do?

Answer

They monitor and regulate the operating regime.

69Question

What distinguishes gasoline from diesel oil by hydrocarbon composition?

Answer

Gasoline contains light hydrocarbons; diesel oil contains heavy hydrocarbons.

70Question

Which applications are listed for engines?

Answer

Automobiles, tractors, trucks, locomotives, marine use, light aircraft, industry, and power generation.

71Question

At the same engine speed, how often does a two-stroke engine cycle compared with a four-stroke engine?

Answer

Twice as often.

72Question

How many degrees crank angle does one crankshaft revolution span?

Answer

360°CA.

73Question

How many degrees crank angle does a four-stroke cycle span?

Answer

720°CA.

74Question

What mean piston-speed range characterizes low-speed engines?

Answer

Approximately 4–6.5 m/s.

75Question

Which signals are needed to record a p–α diagram?

Answer

Signals from a pressure transducer and a crank-angle encoder.

76Question

How often does geometric cylinder volume repeat, and what diagram represents its variation?

Answer

It repeats every crankshaft revolution and is represented by the V–α diagram.

77Question

What does the heat-release characteristic describe?

Answer

The fraction of available fuel energy released during combustion.

78Question

When may an engine's intake and exhaust valves be open simultaneously?

Answer

During valve overlap.

Test yourself with the quiz

Answer 21 questions on Heat Engine Fundamentals.

1. Which description best explains how a heat engine produces mechanical work?

2. What happens to the working fluid's composition over an engine cycle?

Take the quiz →

Read the study guide

Go over the full study guide for Heat Engine Fundamentals.

Read the study guide →

Related classes

Make your own flashcards

Upload your class notes and Revizly writes your flashcards in about a minute.

Flashcard maker